Flagpoles
Fiberglass built to last decades.
Fiberglass, XL, aluminium and indoor models. Manufactured in Spain since 1994.
Designed for 30 years
of continuous exposure.
Non-metallic, non-conductive and chemically stable composite structure. Resistant to UV radiation, atmospheric salinity, freeze–thaw cycles and sustained winds above 100 km/h. No structural maintenance throughout its service life.
The material
60% fiberglass.
Polyester resin matrix.
One-piece laminated structure with a tapered conical geometry. The combination of glass fibre and polyester resin delivers mechanical strength comparable to steel at a fraction of the weight, with no risk of corrosion or oxidation fatigue.
Non-conductive
No earthing required (REBT)
Corrosion-free
Suitable for marine and salt-laden atmospheres
Flexibility
Elastic recovery after wind load
Light weight
11 kg at 4 m · 45 kg at 12 m · 380 kg at 22 m
The finish
Gel Coat finish.
High-density polyester top layer.
Final coating made of a white polyester surface layer applied over the fiberglass laminate. Provides watertightness, UV protection and chemical resistance against atmospheric pollutants. Available in standard white or in any RAL chart colour on request.
RAL chart · selection
The heights
14 heights available.
Explore the data.
Ø tip
65mm
Ø base
140mm
Mast weight
45kg
Base weight
5kg
Recommended flag
1,5 × 6 m
Standard supply in a single piece. Available in two pieces (bolted or push-fit) for easier transport and installation. The 25 m mast is supplied in three pieces. Use ← → to scroll through heights with the keyboard.
The systems
Four hoisting systems.
Same structural base.
6.1
Rotating power arm.
Extended-arm system with an 800 g counterweight that keeps the flag permanently deployed and tensioned regardless of wind speed. The power body rotates freely 360° around the mast axis on an internal bearing, ensuring continuous, silent movement.
Compatible only with vertical (advertising) flags.
- Components
- Power body · Aluminium bar · 800 g counterweight · Carabiner · Clamps
- Heights
- 4 to 12 m
- Finial
- Gold onion or white mushroom
6.2
External halyard with cleat.
Traditional hoisting system using a Ø 5 mm rope that runs along the outside of the mast. The halyard is secured with a cleat bolted to the shaft, allowing the flag to be raised and lowered manually in seconds. A mechanism with no internal components: maximum simplicity, minimum maintenance.
Compatible with horizontal (institutional) and vertical (advertising) flags.
- Components
- Finial · Sleeve · Ø 5 mm halyard · Cleat · Carabiner · Clamps
- Heights
- 4 to 25 m
- Halyard length
- 6 m (4 m mast) up to 43 m (22 m mast)
6.3
Internal halyard with crank.
Winch-type mechanism housed inside the shaft. The Ø 4 mm halyard runs internally through the mast and is operated from a crank at the base. The system keeps the hoisting line hidden, improving the overall aesthetics and protecting the halyard from weathering.
Compatible with horizontal and vertical flags.
- Components
- Finial · Sleeve · Internal winch system · Crank · Ø 4 mm halyard · Anti-return ball · Carabiner · Counterweight · Clamps
- Heights
- 4 to 25 m
- Crank
- 4–9 m model · 10–12 m model · XL 13–25 m model
6.4
Internal halyard with security door.
Variant of the internal system in which the crank is replaced by a lockable door integrated in the shaft. Access to the hoisting mechanism is restricted to authorised personnel by key, eliminating the risk of tampering and vandalism.
Compatible with horizontal and vertical flags.
- Components
- Finial · Sleeve · Lockable security door · Ø 4 mm internal halyard · Anti-return ball · Carabiner · Counterweight · Clamps
- Heights
- 4 to 25 m
Base & installation
Tilting base.
Foundation calculated by zone.
All masts are supplied with a hot-dip galvanised steel hinged base, allowing the shaft to be fully tilted down for maintenance or replacement without dismantling. R2 models for the standard series (4–12 m) and reinforced Box for the XL series (13–25 m).
Inland / rural
HA-25 / B / 20 / IIa
Medium humidity
Coastal (≤ 5 km)
HA-30 / B / 20 / IIIa
Salt-spray resistant
High altitude / snow
HA-30 / B / 20 / IIb + Qb
Freeze–thaw cycles
Underground foundation
Buried concrete block with anchor bolt.
Above-ground foundation
Base bolted onto a reinforced existing slab.
Lighting
Integrated LED lighting.
Three power levels.
Anodised aluminium LED fixtures powered at 24 V. Specifically designed for flag-on-mast lighting, with an 11° beam angle that concentrates the light on the fabric. Service life over 50,000 hours. 2-year warranty.
| LED Core | LED Plus | LED Max | |
|---|---|---|---|
| Power | 24 W | 50 W | 90 W |
| Luminous flux | 2.300 lm | 5.000 lm | 9.500 lm |
| Colour temperature | 3000 / 4000 / 5000 K | ||
| Mast height | 4 – 9 m | 10 – 12 m | 13 – 19 m |
Wind resistance
Certified wind resistance.
For every height, every flag.
Maximum admissible wind speed calculated according to mast height and exposed flag area. Values correspond to ground-level installations under standard atmospheric conditions. For elevated or exposed locations, please consult our technical department.
| Vertical flag 1.5 × 6 m | 12 m mast | 100 km/h |
| Vertical flag 1.8 × 9 m | 18 m mast | 105 km/h |
| Vertical flag 1.8 × 11 m | 22 m mast | 100 km/h |
Manufacturing
Fully manufactured in Spain.
Bureau Veritas quality control.
Design, lamination, machining, finishing and assembly carried out in our own plant. All structural and mechanical components fall under the Bureau Veritas quality programme. In-house technical service for installation, relocation and maintenance across the Iberian Peninsula.
30+
years of manufacturing
3
Europe, America and Africa · distribution network
BV
Bureau Veritas · quality programme
100%
In-house installation
Request a technical proposal
Request a technical proposal.
Product configurator available. Personal guidance from our technical department.